Mindray DPM 1 Betreibershandbuch Seite 14
- Seite / 120
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1-2
1.1.1 Warnings
WARNING
This monitor is not applicable for prolonged and continuous SpO
2
monitoring,
which may increase the risks of irritation and burns at the site of the sensor.
This monitor is not applicable for prolonged and continuous temperature
monitoring for more than 5 minutes.
This monitor is intended for use by qualified clinical physicians or well-trained
nurses in the specified places.
It is your responsibility to verify the device and accessories can function safely
and normally before use
The disposable accessories should be disposed of in accordance with the hospital
regulations.
A possible fire or explosion hazard exists when used in the presence of
flammable anesthetics or other flammable or explosive substances in
combination with air, oxygen-enriched environments, or nitrous oxide.
Do not rely exclusively on the audible alarm system for patient monitoring.
Adjustment of alarm volume to a low level or off may result in a hazard to the
patient. Remember that alarm settings should be customized according to
different patient situations and always keeping the patient under close
surveillance is the most reliable way for safe patient monitoring.
Opening the monitor housing presents a risk of hazard due to electrical shock.
All servicing and future upgrades to this equipment must be carried out by
personnel trained and authorized by Mindray DS only.
Do not touch the patient or equipment connected to the patient during
defibrillation. A risk of serious injury or death is present.
When using the equipment with electrosurgical units (ESU), make sure the
patient is safe.
Dispose of the package material according to the applicable waste control
regulations and keep it out of children’s reach.
The device must be connected to a properly installed power outlet with
protective earth contacts only. If the installation does not provide for a
protective earth conductor, disconnect the monitor from the power line and
operate it on battery power, if possible.
- DPM 3 Vital Signs Monitor 1
- Operator’s Manual 1
- Revision History 3
- Warranty 5
- Exemptions 5
- Return Policy 6
- Contact Information 6
- Preface 7
- Contents 9
- 1 Safety 13
- 1.1.1 Warnings 14
- WARNING 14
- 1.1.2 Cautions 15
- CAUTION 15
- 1.2 Equipment Symbols 16
- 2 The Basics 19
- 2.1.3 Components 20
- 2.1.4 Functions 20
- 2.2 Appearance 21
- 2.2.2 Rear Panel 25
- 2.2.3 Recorder 26
- 2.3 Display 27
- 2.4 Battery 28
- 2.4.1 Battery Maintenance 29
- 2.4.2 Battery Recycling 30
- Installation and Maintenance 31
- 3.1.4 Bracket Mounting 32
- 3.1.5 Installation Method 33
- 3.2 Maintenance 37
- 3.2.1 Inspection 38
- 3.2.2 Cleaning 38
- 3.2.3 Disinfection 40
- 4 Menus and Screens 41
- 4.2 System Setup 42
- 4.2.2 Network Setup 43
- 4.2.3 Time Setup 44
- 4.2.4 User Maintenance 44
- 4.2.5 Nurse Call Setup 45
- WARNING 46
- 4.2.6 Version 46
- 4.2.7 Configuration 46
- 4.3 Normal Screen 47
- 4.4 Trend Screen 48
- 4.5 Standby State 49
- 5 Alarms 51
- 5.2 Alarm Indications 52
- 5.2.1 Alarm Lamp 53
- 5.2.2 Audible Alarms 53
- 5.2.3 Alarm Messages 53
- 5.3 Alarm Status 54
- 5.3.3 Alarms Paused 55
- 5.3.4 Alarm Silenced 56
- 5.3.5 Status Switchover 56
- 5.5 Setting Alarms 57
- Sensor Off Alarm 58
- 5.7 When an Alarm Occurs 58
- 6 Recording 59
- 6.3 Loading Paper 60
- 6.4 Removing Paper Jam 61
- Monitoring 63
- 7.2 Safety 64
- 7.3 Monitoring Procedure 65
- 7.4 Measurement Limitations 65
- 7.5 Masimo Information 66
- 7.6 Nellcor Information 66
- 8 NIBP Monitoring 67
- 8.2 Monitoring Procedure 68
- 8.2.2 Operation Guides 69
- 8.3 Measurement Limitations 70
- 8.4.2 Resetting NIBP 71
- 8.4.3 Calibrating NIBP 72
- 8.4.4 NIBP Leakage Test 73
- 9 TEMP Monitoring 75
- 9.2 Temperature Setup 76
- 9.3 Monitoring Procedure 76
- ™ TEMP Probe 79
- 9.5 Precautions 80
- 10 Accessories 81
- 10.2 NIBP Accessories 83
- 10.3 TEMP Accessories 84
- 10.4 Others 84
- A Product Specifications 85
- A.3 Power Requirements 86
- A.4 Hardware Specification 87
- A.5 Signal Output 88
- Specification 88
- A.6.2 Masimo SpO 89
- A.7 NIBP Specification 90
- A.8 TEMP Specification 91
- C.2 Technical Alarm Messages 97
- C.2.3 Mindray DS SpO 100
- Module Alarm Messages 100
- C.2.4 Masimo SpO 101
- C.2.5 Nellcor SpO 103
- C.3 Prompt Messages 108
- FOR YOUR NOTES 110
- D Factory Defaults 111
- D.2 System Setup 112
- D.3 Alarm Limit 113
- E Symbols and Abbreviation 115
- E.2 Symbols 116
- E.3 Abbreviations 117
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Mindray DPM 1
(274 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern